2090-CSWM1DF-14AA09 单根电缆

目录号由各种字符组成，每个字符标识该组件的一个特定选项。使用下面的目录编号图表来了解组件的配置。有关产品可用性的问题，请联系您的Allen-Bradley经销商。

清除物品内部和周围的所有包装材料。开箱后，根据订购单核对目录号，目视检查电缆和每个连接器是否损坏。如有必要，立即通知承运人任何运输损坏。
电缆以线圈的形式储存和运输。在拉直电缆之前，电缆保持这种形状。要拉直电缆，可以从其中点悬挂一根短电缆，或将一根长电缆沿直线放在地板上。在接下来的24小时内，电缆中的任何线圈都将被拉直。这种做法使电缆更容易安装。

单根电缆使用的电缆技术是相同的，无论目录号如何。每根电缆的不同之处在于引线准备和反馈导体端子。
•2090-CSxM1DF电缆导体具有飞引线和引线制备，专为Kinetix 5500伺服驱动器设计。不需要现场铅准备。
•2090-CSxM1DE电缆包括2198-KITCON-DSL连接器套件。该套件与反馈导体预组装，飞引线功率导体的引线准备是专门为Kinetix 5700伺服驱动器设计的。不需要现场铅准备。
•2090-CSxM1DG电缆导体具有飞引线和引线制备，专为Kinetix 5500或Kinetix 5700伺服驱动器设计。不需要现场引线准备，但是，2090-CSxM1DG电缆引线比2090-CSxM1DF电缆引线长，以适应任一驱动器系列。

这些数字说明了如何测量弯曲半径和电缆弯曲的地方可以在单电机电缆上。在系统安装过程中，布放电缆时，请与电缆引脚和规格表配合使用。

为了满足Kinetix 5700伺服驱动系统上的电机制动电路的当前要求，电缆长度超过50米(164英尺)，2090-CSBM1DE (B系列)电缆可与18 AWG制动导体一起使用。B系列电缆设计用于电缆长度从51米(167英尺)到90米(294英尺)的应用，可提供1.0米(3.3英尺)的增量。对于需要1.0米(3.3英尺)…50米(164英尺)电缆长度的Kinetix 5700驱动系统，2090-CSBM1DE (A系列)电缆仍然可用。

Catalog numbers consist of various characters, each of which identifies a specific option for that component. Use the catalog numbering charts below to understａnd the configuration of your component. For questions regarding product availability, contact your Allen-Bradley distributor.

Remove all packing material from within and around the item. After unpacking, verify the catalog number against the purchase order and visually inspect the cable and each connector for damage. If necessary, notify the carrier of any shipping damage immediately.
Cables are stored and shipped in a coil. Cables retain this shape until you straighten the cable. To straighten a cable, hang a short cable from its midpoint or lay a long cable on the floor in a straight line. Any coiling that remains in the cable is straightened out within the next 24 hours. This practice makes the cable easier to install.

The cable technology used in single cables is the same regardless of the catalog number. What is different about each cable is the lead preparation and feedback conductor terminations.
• 2090-CSxM1DF cable conductors have flying-leads and lead preparation that is designed specifically for Kinetix 5500 servo drives. No onsite lead preparation is required.
• 2090-CSxM1DE cables include the 2198-KITCON-DSL connector kit. The kit is pre-assembled with the feedback conductors and lead preparation for the flying-lead power conductors is designed specifically for Kinetix 5700 servo drives. No on-site lead preparation is required.
• 2090-CSxM1DG cable conductors have flying-leads and lead preparation that is designed for either Kinetix 5500 or Kinetix 5700 servo drives. No on-site lead preparation is required, however, 2090-CSxM1DG cable leads are longer than 2090-CSxM1DF cable leads to accommodate either drive family.

These figures illustrate how to measure the bend radius and where cable bends can be made on single motor cables. Use these figures with the cable pinout and specification tables that follow when routing cables during system installation.

To meet the current requirements of motor brake circuits on Kinetix 5700 servo drive systems with cable lengths that exceed 50 m (164 ft), the 2090-CSBM1DE (series B) cables are available with 18 AWG brake conductors. Series B cables are designed for applications with cable lengths from 51 m (167 ft)…90 m (294 ft) and are available in 1.0 m (3.3 ft) increments. For Kinetix 5700 drive systems requiring cable lengths from 1.0 m (3.3 ft)…50 m (164 ft), the 2090-CSBM1DE (series A) cables are still available.